Axxius 800USER MANUALPart Number: 770-0104 AGProduct Release: 2.2May 2004
x Axxius 800 - Release 2.2PrefaceWarrantyWarranty Product ReturnsBefore returning any equipment to Carrier Access Corporation, first contact the distr
4-28 Axxius 800 - Release 2.2ConfigurationSetup of DS0 Management ChannelTesting the DS0 Management ChannelAfter the DS0 management channels has been
CHAPTERCLI CommandsIn this Chaptern Command Line Interface Helpn CLI Commands
5-2 Axxius 800 - Release 2.2CLI CommandsCommand Line Interface HelpDuring a CLI session, help is available at any time.? or helpType a ? (or "he
Axxius 800 - Release 2.2 5-3CLI Commandsthe [TAB] feature, scroll through all available options for this command: > set [TAB] will scroll
5-4 Axxius 800 - Release 2.2CLI CommandsCLI CommandsFor maneuverability through these commands, all command names in blue or italics are hyperlinked.a
Axxius 800 - Release 2.2 5-5CLI Commandsaco (Alarm Cut Off)aco (Alarm Cut Off)Use the aco command to activate the Alarm Cut Off, which opens the alarm
5-6 Axxius 800 - Release 2.2CLI CommandsaddaddUse the add command to create users, interfaces, services or profiles.See the following sections for det
Axxius 800 - Release 2.2 5-7CLI Commandsaddadd (ds1) aisUse the add (ds1) ais command to add DS1s to a list for the AIS Forwarding feature. The DS1 en
5-8 Axxius 800 - Release 2.2CLI Commandsaddadd (router) dhcp server optionUse the add (router) dhcp server option command to add optional DHCP server
Axxius 800 - Release 2.2 5-9CLI Commandsaddadd (router) dns proxyUse the add (router) dns proxy command to enable DNS proxy and add a remote DNS serve
TABLE OF CONTENTSPrefaceCompliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iiiSafety . .
5-10 Axxius 800 - Release 2.2CLI Commandsaddadd (router) snmp communityUse the add (router) snmp community command to add a SNMP community to an inter
Axxius 800 - Release 2.2 5-11CLI Commandsaddadd (router) snmp trapUse the add (router) snmp trap command to specify a destination to send SNMP trap me
5-12 Axxius 800 - Release 2.2CLI Commandsaddadd (router) static dns hostUse the add (router) static dns host command to add a static DNS host record f
Axxius 800 - Release 2.2 5-13CLI Commandsaddadd (router) uploaduserUse the add (router) uploaduser command to specify a host that is allowed to upload
5-14 Axxius 800 - Release 2.2CLI Commandsaddadd (router-lan) filter Use the add (router-lan) filter commands to add filters to the specified LAN inter
Axxius 800 - Release 2.2 5-15CLI Commandsaddadd (router-lan) filter customUse the add (router-lan) filter custom command to add a custom filter to the
5-16 Axxius 800 - Release 2.2CLI CommandsaddEthernet Frame and IP Packet FormatEthernet 802.3 (raw) Frame - Datalink Header6 bytes 6 bytes 2 bytes 46
Axxius 800 - Release 2.2 5-17CLI Commandsaddadd (router-lan) filter protocolUse the add (router-lan) filter protocol command to add a protocol filter
5-18 Axxius 800 - Release 2.2CLI Commandsaddadd (router-lan) secondary ip addressUse the add (router-lan) secondary ip address command to add a second
Axxius 800 - Release 2.2 5-19CLI Commandsaddadd (router-lan) static Use the add (router-lan) static commands to add static elements on the specified L
xii Axxius 800 - Release 2.2Table of Contents Low Speed Protection card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6Power
5-20 Axxius 800 - Release 2.2CLI Commandsaddadd (router-lan) static ip networkUse the add (router-lan) static ip network command to add a static IP ne
Axxius 800 - Release 2.2 5-21CLI Commandsaddadd (router-lan) static ipx networkUse the add (router-lan) static ipx network command to add a static IPX
5-22 Axxius 800 - Release 2.2CLI Commandsaddadd (router-lan) static mac addressUse the add (router-lan) static mac address command to add a static MAC
Axxius 800 - Release 2.2 5-23CLI Commandsaddadd (router-wan) firewallUse the add (router-wan) firewall command to add a firewall rule to a WAN.Syntax:
5-24 Axxius 800 - Release 2.2CLI Commandsadd{service}{dest-ip-addr/bits}The destination IP Address and number of significant bits. The IP Address is i
Axxius 800 - Release 2.2 5-25CLI Commandsadd{src-ip-addr/bits}The destination IP address and number of significant bits. The address "0.0.0.0/0&q
5-26 Axxius 800 - Release 2.2CLI Commandsaddadd (router-wan) gre networkUse the add (router-wan) gre network command to add a "by network" G
Axxius 800 - Release 2.2 5-27CLI Commandsaddadd (router-wan) nat bypassUse the add (router-wan) nat bypass command to add subnets to the list of sourc
5-28 Axxius 800 - Release 2.2CLI Commandsaddadd (router-wan) staticUse the add (router-wan) static commands to add static elements on the specified WA
Axxius 800 - Release 2.2 5-29CLI Commandsaddadd (router-wan) static ip networkUse the add (router-wan) static ip network command to add a static IP ne
Axxius 800 - Release 2.2 xiii Table of Contents 2 Physical InstallationUnpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . .
5-30 Axxius 800 - Release 2.2CLI Commandsaddadd (router-wan) static ipx networkUse the add (router-wan) static ipx network command to add a static IPX
Axxius 800 - Release 2.2 5-31CLI Commandsaddadd (router-wan) static mac addressUse the add (router-wan) static mac address command to add a static MAC
5-32 Axxius 800 - Release 2.2CLI Commandsaddadd (router-wan) static nat addressUse the add (router-wan) static nat address command to add a static NAT
Axxius 800 - Release 2.2 5-33CLI CommandsalarmsalarmsUse the alarms command to display the active alarms. The report can be filtered by address, categ
5-34 Axxius 800 - Release 2.2CLI CommandsclearclearUser the clear command to clear logs, performance data and tables.clear (ds1)clear (ds3)clear keycl
Axxius 800 - Release 2.2 5-35CLI Commandsclearclear (ds1)Use the clear (ds1) command to clear specified DS1 performance data.Syntax: clear {ds1-addr}
5-36 Axxius 800 - Release 2.2CLI Commandsclearclear (ds3)Use the clear (ds3) command to clear specified DS3 performance data. Note this command applie
Axxius 800 - Release 2.2 5-37CLI Commandsclearclear keyUse the clear key command to remove a specific keyed feature. To acquire a feature key code, co
5-38 Axxius 800 - Release 2.2CLI Commandsclearclear (router) ip address tableUse the clear (router) ip address table command to flush the learned entr
Axxius 800 - Release 2.2 5-39CLI Commandsclearclear (router) performanceUse the clear (router) performance command to clear the runtime statistics tha
xiv Axxius 800 - Release 2.2Table of Contents Quick Configuration Reload. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11Setup
5-40 Axxius 800 - Release 2.2CLI CommandsconnectconnectUse the connect command to create two-way connections between any DS0 channels of the service o
Axxius 800 - Release 2.2 5-41CLI Commandsconnectconnect (router-trunk) (t1)Use the connect (router-trunk) (t1) command to create two-way connections b
5-42 Axxius 800 - Release 2.2CLI CommandsdeletedeleteUse the delete command to remove users, interfaces, services or profiles.See the following sectio
Axxius 800 - Release 2.2 5-43CLI Commandsdeletedelete (ds1) aisUse the delete (ds1) ais command to delete DS1s from the AIS DS1 list. The DS1 that is
5-44 Axxius 800 - Release 2.2CLI Commandsdeletedelete (router) dhcp server optionUse the delete (router) dhcp server option command to delete optional
Axxius 800 - Release 2.2 5-45CLI Commandsdeletedelete (router) remoteUse the delete (router) remote command to delete a remote WAN profile from the WA
5-46 Axxius 800 - Release 2.2CLI Commandsdeletedelete (router) snmp trapUse the delete (router) snmp trap command to delete a trap destination from th
Axxius 800 - Release 2.2 5-47CLI Commandsdeletedelete (router) uploaduserUse the delete (router) uploaduser command to remove an existing host that is
5-48 Axxius 800 - Release 2.2CLI Commandsdeletedelete (router-lan) filterUse the delete (router-lan) filter command to delete a single filter rule fro
Axxius 800 - Release 2.2 5-49CLI Commandsdeletedelete (router-lan) secondary ip addressUse the delete (router-lan) secondary ip address command to del
Axxius 800 - Release 2.2 xv Table of Contents clear key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-50 Axxius 800 - Release 2.2CLI Commandsdeletedelete (router-lan) staticUse the delete (router-lan) static commands to delete static elements from th
Axxius 800 - Release 2.2 5-51CLI Commandsdeletedelete (router-lan) static ip networkUse the delete (router-lan) static ip network command to delete a
5-52 Axxius 800 - Release 2.2CLI Commandsdeletedelete (router-lan) static ipx networkUse the delete (router-lan) static ipx network command to delete
Axxius 800 - Release 2.2 5-53CLI Commandsdeletedelete (router-lan) static mac addressUse the delete (router-lan) static mac address command to delete
5-54 Axxius 800 - Release 2.2CLI Commandsdeletedelete (router-wan) gre networkUse the delete (router-wan) gre network command to delete a "by net
Axxius 800 - Release 2.2 5-55CLI Commandsdeletedelete (router-wan) staticUse the delete (router-wan) static commands to delete a static element from t
5-56 Axxius 800 - Release 2.2CLI Commandsdeletedelete (router-wan) static ip networkUse the delete (router-wan) static ip network command to delete a
Axxius 800 - Release 2.2 5-57CLI Commandsdeletedelete (router-wan) static mac addressUse the delete (router-wan) static mac address command to delete
5-58 Axxius 800 - Release 2.2CLI Commandsdisconnectdelete userThe delete user command will remover a user created by the add user command. Syntax: del
Axxius 800 - Release 2.2 5-59CLI CommandsexitexitUse the exit command to log out of the Command Line Interface (CLI). Syntax: exitExample: > exitLo
xvi Axxius 800 - Release 2.2Table of Contents log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-60 Axxius 800 - Release 2.2CLI Commandsloadload WARNING! BEFORE LOADING A DOWN-LEVEL OF ROUTER CODE TO AN ADIT, SAVE THE CONFIGURATION TO A FILE.
Axxius 800 - Release 2.2 5-61CLI Commandsloadload xmodemUse the load xmodem command to download software via Xmodem. This command is only available wi
5-62 Axxius 800 - Release 2.2CLI CommandslogloglogDisplays the event log. Where the optional [slot:port:channel], [category], and [severity] are varia
Axxius 800 - Release 2.2 5-63CLI CommandspingpingpingUse the ping command to perform a ping test from the Controller and report the result. If the hos
5-64 Axxius 800 - Release 2.2CLI CommandsprintprintUse the print command to display the help information or print the configuration file.Syntax: print
Axxius 800 - Release 2.2 5-65CLI Commandsrename (router)print helpPrint the complete help file to the screen.Syntax: print helpExample: print helpThis
5-66 Axxius 800 - Release 2.2CLI Commandsresetresetreset (controller)Use the reset (controller) command to reboot the system. Reset alone will reboot
Axxius 800 - Release 2.2 5-67CLI Commandsrestorereset (router) coldbootUse the reset (router) coldboot command to reboot the Router. This will reboot
5-68 Axxius 800 - Release 2.2CLI CommandsrtrpingrtrpingUse the rtrping command to request that the Router perform a ping test and report the result.Sy
Axxius 800 - Release 2.2 5-69CLI Commandssetset set alarms set (ocudp) baudset autoexit set (ocudp) loopbackset (bri) set (ocudp) loopdetectset (bri)
Axxius 800 - Release 2.2 xvii Table of Contents set ipds0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-70 Axxius 800 - Release 2.2CLI Commandssetset (router-lan) ip address set (router-wan) natset (router-lan) ipx network set (router-wan) otherset (ro
Axxius 800 - Release 2.2 5-71CLI Commandssetset alarmsUse the set alarms to manually set an alarm state for testing.Syntax: set alarms {critical|major
5-72 Axxius 800 - Release 2.2CLI Commandssetset (bri)Use the set (bri) command to setup the ISDN BRI card. Syntax: set {bri-addr} {day|hour} {es|ses}
Axxius 800 - Release 2.2 5-73CLI Commandssetset (bri) modeUse the set (bri) mode command to set the mode for the ISDN BRI Service. Syntax: set {bri_ca
5-74 Axxius 800 - Release 2.2CLI Commandssetset cclabelUse the set cclable command to set a user defined cross-connect label.Syntax: set cclabel {addr
Axxius 800 - Release 2.2 5-75CLI Commandssetset clock (1 and 2)
5-76 Axxius 800 - Release 2.2CLI Commandssetset (ds0)Use the set (ds0) command to setup one or all DS0s in a DS1. The command specifies DS0 or range o
Axxius 800 - Release 2.2 5-77CLI Commandssetset(ds0) typeUse the set (ds0) type command to setup one or all DS0s in a DS1 signal type. Syntax: set {ds
5-78 Axxius 800 - Release 2.2CLI Commandssetset (ds1)Use the set (ds1) command to set up DS1 interfaces. The command specifies a range of interfaces a
Axxius 800 - Release 2.2 5-79CLI Commandssetid Set the DS1 circuit identification name. This is the same as dsx1Circuit Identifier from DS1 MIB transm
xviii Axxius 800 - Release 2.2Table of Contents set (router) rip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
5-80 Axxius 800 - Release 2.2CLI CommandssetthresholdSet default thresholds for a DS1. Defaults for all are 0. day Set threshold for a daily interv
Axxius 800 - Release 2.2 5-81CLI Commandssetset (ds1 card)Use the set (ds1 card) commands to configure DS1 card types. These commands apply to the Qua
5-82 Axxius 800 - Release 2.2CLI Commandssetset (ds1 card) adpcm mapUse the set (ds1 card) adpcm map command to set voice compression map on the Quad
Axxius 800 - Release 2.2 5-83CLI Commandssetset (ds3)Use the set (ds3) command to set up DS3 interfaces. The command specifies a range of interfaces a
5-84 Axxius 800 - Release 2.2CLI Commandssetframe Set the DS3 frame PMDL ID stringCommand syntax: set {ds3-addr} frame {"string"}{"stri
Axxius 800 - Release 2.2 5-85CLI Commandssetreversion Set protection reversion on the DS3 off Disable protection reversion of loopback requests
5-86 Axxius 800 - Release 2.2CLI Commandssetset ethernet ip addressUse the set ethernet ip address command to set the Ethernet address for the Axxius
Axxius 800 - Release 2.2 5-87CLI Commandssetset (fxo) Use the
5-88 Axxius 800 - Release 2.2CLI Commandssetset (fxsPS or fxsPSM)Use the set (fxsPS or fxsPSM) command to setup voice channels of an Single Channel PO
Axxius 800 - Release 2.2 5-89CLI Commandssetset idleUse the set idle command to set the system-wide idle code sent on DS0s. Syntax: set idle {pattern}
Axxius 800 - Release 2.2 xix Table of Contents set (v35) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-90 Axxius 800 - Release 2.2CLI Commandssetset ipds0Use the set ipds0 command to setup the DS0 management channel. Note: the DS0 selected as the DS0
Axxius 800 - Release 2.2 5-91CLI Commandssetset keyUse the set key command to enable a specific keyed feature. To acquire a feature key code, contact
5-92 Axxius 800 - Release 2.2CLI Commandssetset login supportUse the set login support command to enable or disable the internal login accounts for Ca
Axxius 800 - Release 2.2 5-93CLI Commandssetset lsprotect enable/disableUse the set lsprotect enable/disable command to set the global enable or disab
5-94 Axxius 800 - Release 2.2CLI Commandssetset lsprotect nonrevertiveUse the set lsprotect nonrevertive command to set low speed protected port(s) to
Axxius 800 - Release 2.2 5-95CLI Commandssetset lsprotect removeUse the set lsprotect remove command to remove port from protected mode. Syntax: set l
5-96 Axxius 800 - Release 2.2CLI Commandssetset lsprotect revertiveUse the set lsprotect revertive command to set low speed protected port(s) to rever
Axxius 800 - Release 2.2 5-97CLI Commandssetset (ocudp) baudUse the set (ocudp) baud command to configure the Baud Rate for OCU-DP ports. Syntax: set
5-98 Axxius 800 - Release 2.2CLI Commandssetset (ocudp) loopbackUse the set (ocudp) loopback command to manually set OCU/CSU loopback tests. Syntax: s
Axxius 800 - Release 2.2 5-99CLI Commandssetset (ocudp) loopdetectUse the set (ocudp) loopdetect to configure the OCU non-latching/latching loopback c
Copyright 2004 Carrier Access Corporation. All rights reserved.The information presented in this manual is subject to change without notice and does n
xx Axxius 800 - Release 2.2Table of Contents show (router) lmi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-197sho
5-100 Axxius 800 - Release 2.2CLI Commandssetset (ocudp) mvecUse the set (ocudp) mvec to set Majority Vote Error Correction (MVEC). Syntax: set {ocudp
Axxius 800 - Release 2.2 5-101CLI Commandssetset (ocudp) selftestUse the set (ocudp) selftest to initiate the OCU-DP card to perform a self test. This
5-102 Axxius 800 - Release 2.2CLI Commandssetset (router) autologoutUse the set (router) autologout command to set the period of time of inactivity af
Axxius 800 - Release 2.2 5-103CLI Commandssetset (router) dhcp Use the set (router) dhcp commands to configure the DHCP functions.set (router) dhcp di
5-104 Axxius 800 - Release 2.2CLI Commandssetset (router) dhcp server dnsserverUse the set (router) dhcp server dnsserver command to set the IP addres
Axxius 800 - Release 2.2 5-105CLI Commandssetset (router) dhcp server durationUse the set (router) dhcp server duration command to set the lease durat
5-106 Axxius 800 - Release 2.2CLI Commandssetset (router) dhcp server netbios nodetypeUse the set (router) dhcp server netbios nodetype command to set
Axxius 800 - Release 2.2 5-107CLI Commandssetset (router) dhcp server startaddrUse the set (router) dhcp server startaddr command to enable the DHCP s
5-108 Axxius 800 - Release 2.2CLI Commandssetset (router) dns Use the set (router) dns commands to set Domain Name Server (DNS) options.set (router) d
Axxius 800 - Release 2.2 5-109CLI Commandssetset (router) dns resolverUse the set (router) dns resolver command to enable/disable use of DNS resolver
Axxius 800 - Release 2.2 xxi Table of Contents status (adpcm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-
5-110 Axxius 800 - Release 2.2CLI Commandssetset (router) enhanced securityUse the set (router) enhanced security command to enable or disable enhance
Axxius 800 - Release 2.2 5-111CLI Commandssetset (router) lmi pollUse the set (router) lmi poll command to specify the Local Management Interface (LMI
5-112 Axxius 800 - Release 2.2CLI Commandssetset (router) login promptUse the set (router) login prompt command to enable/disable the login prompt on
Axxius 800 - Release 2.2 5-113CLI Commandssetset (router) ntp pollUse the set (router) ntp poll command to specify polling of the NTP server every def
5-114 Axxius 800 - Release 2.2CLI Commandssetset (router) ntp timezoneUse the set (router) ntp timezone command to specify the timezone offset relativ
Axxius 800 - Release 2.2 5-115CLI Commandssetset (router) portUse the set (router) port command to set port characteristics on a Terminal Server Route
5-116 Axxius 800 - Release 2.2CLI Commandssetset (router) port databitsUse the set (router) port databits command to set the data bits on a TSR port.S
Axxius 800 - Release 2.2 5-117CLI Commandssetset (router) port flowcontrolUse the set (router) port flowcontrol command to set the flow control on a T
5-118 Axxius 800 - Release 2.2CLI Commandssetset (router) port inactivity timerUse the set (router) port inactivity timer command to set the inactivit
Axxius 800 - Release 2.2 5-119CLI Commandssetset (router) port nameUse the set (router) port name command to set define name for a TSR port.Syntax: se
xxii Axxius 800 - Release 2.2Table of Contents telnet (router) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5-120 Axxius 800 - Release 2.2CLI Commandssetset (router) port passiveUse the set (router) port passive command to set the TSR port to passive. This c
Axxius 800 - Release 2.2 5-121CLI Commandssetset (router) port promptUse the set (router) port prompt command to set the authentication prompt on a TS
5-122 Axxius 800 - Release 2.2CLI Commandssetset (router) port stopbitsUse the set (router) port stopbits command to set the number of stop bits on a
Axxius 800 - Release 2.2 5-123CLI Commandssetset (router) port tbos map displayUse the set (router) port tbos map display command to set a TBOS (Telem
5-124 Axxius 800 - Release 2.2CLI Commandssetset (router) port typeUse the set (router) port type command to set the application being used for a RS-2
Axxius 800 - Release 2.2 5-125CLI Commandssetset (router) ppp authUse the set (router) ppp auth command to configure the PPP (Point-to-Point Protocol)
5-126 Axxius 800 - Release 2.2CLI Commandssetset (router) ppp auth byremote userSyntax: set {rtr_card-addr} ppp auth byremote user {profilename|"
Axxius 800 - Release 2.2 5-127CLI Commandssetset (router) ppp securityUse the set (router) ppp security command to set up the local external security
5-128 Axxius 800 - Release 2.2CLI Commandssetset (router) ppp security serverSyntax: set {rtr_card-addr} ppp security server {none|radius|tacacs}Examp
Axxius 800 - Release 2.2 5-129CLI Commandssetset (router) proxyUse the set (router) proxy command to enable/disable proxy ARP mode on the Router. This
Axxius 800 - Release 2.2 xxiii Table of Contents Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-130 Axxius 800 - Release 2.2CLI CommandssetThere are numerous cases of IP address assignments for the proxy and each case causes slightly different
Axxius 800 - Release 2.2 5-131CLI Commandssetset (router) rebootUse the set (router) reboot command to set automatic reboot after an upload of code or
5-132 Axxius 800 - Release 2.2CLI Commandssetset (router) snmpUse the set (router) snmp command to set the SNMP contact, location and name on the spec
Axxius 800 - Release 2.2 5-133CLI Commandssetset (router) snmp nameUse the set (router) snmp name command to set the value of sysName on the specified
5-134 Axxius 800 - Release 2.2CLI Commandssetset (router) stpUse the set (router) stp commands to configure the Spanning Tree Protocol on the Router.
Axxius 800 - Release 2.2 5-135CLI Commandssetset (router) stp bridge maxageUse the set (router) stp bridge maxage command to configure Spanning Tree m
5-136 Axxius 800 - Release 2.2CLI Commandssetset (router) stp enable/disableUse the set (router) stp enable/disable command to enable and disable Span
Axxius 800 - Release 2.2 5-137CLI Commandssetset (router) syslogUse the set (router) syslog commands to configure the Router to send alarm and event m
5-138 Axxius 800 - Release 2.2CLI Commandssetset (router) syslog levelUse the set (router) syslog level command to set the Syslog severity level. Even
Axxius 800 - Release 2.2 5-139CLI Commandssetset (router-lan) filter forwardUse the set (router-lan) filter forward command to specify the forwarding
xxiv Axxius 800 - Release 2.2Table of Contents 9 ISDN BRI CardOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-140 Axxius 800 - Release 2.2CLI Commandssetset (router-lan) framingUse the set (router-lan) framing command to specify which Ethernet frame types ar
Axxius 800 - Release 2.2 5-141CLI Commandssetset (router-lan) gatewayUse the set (router-lan) gateway command to specify a default IP gateway for the
5-142 Axxius 800 - Release 2.2CLI Commandssetset (router-lan) ip addressUse the set (router-lan) ip address command to specify an IP address for the s
Axxius 800 - Release 2.2 5-143CLI Commandssetset (router-lan) ipx networkUse the set (router-lan) ipx network command to specify IPX network numbers f
5-144 Axxius 800 - Release 2.2CLI Commandssetset (router-lan) phyUse the set (router-lan) phy command to specify the Ethernet PHY (physical specificat
Axxius 800 - Release 2.2 5-145CLI Commandssetset (router-lan) ripUse the set (router-lan) rip commands to specify RIP for the specified LAN interface.
5-146 Axxius 800 - Release 2.2CLI Commandssetset (router-lan) rip ipx Use the set (router-lan) rip ipx command to specify the IPX RIP and SAP for the
Axxius 800 - Release 2.2 5-147CLI Commandssetset (router-lan) stpUse the set (router-lan) stp commands to configure the Spanning Tree Protocol on this
5-148 Axxius 800 - Release 2.2CLI Commandssetset (router-lan) stp port costUse the set (router-lan) stp port cost command to configure Spanning Tree p
Axxius 800 - Release 2.2 5-149CLI Commandssetset (router-lan) up/downUse the set (router-lan) up/down command to set the specified LAN interface up or
Axxius 800 - Release 2.2 xxv Table of Contents Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6Env
5-150 Axxius 800 - Release 2.2CLI Commandssetset (router-trunk) encapsulationUse the set (router-trunk) encapsulation command to specify the encapsula
Axxius 800 - Release 2.2 5-151CLI Commandssetset (router-trunk) speedUse the set (router-trunk) speed command to specify the data speed for each DS0 i
5-152 Axxius 800 - Release 2.2CLI Commandssetset (router-wan) dlciUse the set (router-wan) dlci command to set the DLCI (Data Link Connection Identifi
Axxius 800 - Release 2.2 5-153CLI Commandssetset (router-wan) greUse the set (router-wan) gre command to configure Generic Routing Encapsulation tunne
5-154 Axxius 800 - Release 2.2CLI Commandssetset (router-wan) gre ipUse the set (router-wan) gre ip command to configure the GRE tunneling of the IP p
Axxius 800 - Release 2.2 5-155CLI Commandssetset (router-wan) ipUse the set (router-wan) ip command to set the IP traffic handling on the WAN interfac
5-156 Axxius 800 - Release 2.2CLI Commandssetset (router-wan) ipxUse the set (router-wan) ipx command to set the IPX traffic handling on the specified
Axxius 800 - Release 2.2 5-157CLI Commandssetset (router-wan) natUse the set (router-wan) nat commands to configure Network Address Translation (NAT)
5-158 Axxius 800 - Release 2.2CLI Commandssetset (router-wan) nat enable/disableUse the set (router-wan) nat command to enable and disable Network Add
Axxius 800 - Release 2.2 5-159CLI Commandssetset (router-wan) otherUse the set (router-wan) other command to set the traffic handling of protocols oth
xxvi Axxius 800 - Release 2.2Table of Contents 12 Power SupplyOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-160 Axxius 800 - Release 2.2CLI Commandssetset (router-wan) pppUse the set (router) ppp command to configure the PPP (Point-to-Point Protocol) on th
Axxius 800 - Release 2.2 5-161CLI Commandssetset (router-wan) ppp compressionUse the set (router-wan) ppp compression command to configure the PPP com
5-162 Axxius 800 - Release 2.2CLI Commandssetset (router-wan) ripUse the set (router-wan) rip commands to set the type of RIP updates on the WAN inter
Axxius 800 - Release 2.2 5-163CLI Commandssetset (router-wan) stpUse the set (router-wan) stp commands to configure the Spanning Tree Protocol on the
5-164 Axxius 800 - Release 2.2CLI Commandssetset (router-wan) stp port costUse the set (router-wan) stp port cost command to configure Spanning Tree p
Axxius 800 - Release 2.2 5-165CLI Commandssetset (router-wan) trunkUse the set (router-wan) trunk command to configure the trunk port or multilink gro
5-166 Axxius 800 - Release 2.2CLI Commandssetset screenUse the set screen command to set the height of the scrolling output screen, in number of lines
Axxius 800 - Release 2.2 5-167CLI Commandssetset snmpUse the set snmp command to set the Simple Network Management Protocol (SNMP) MIB-II System Group
5-168 Axxius 800 - Release 2.2CLI Commandssetset timeUse the set time command to set the time. Syntax: set time {hh:mm:ss} Example: set time 12:00:00T
Axxius 800 - Release 2.2 5-169CLI Commandssetset userUse the set user command to modify attributes for a specific user that have been created with the
Axxius 800 - Release 2.2 xxvii Table of Contents Card Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-170 Axxius 800 - Release 2.2CLI Commandssetset (v35)Use the set (v35) command to setup V.35 ports. The command specifies the range of channels withi
Axxius 800 - Release 2.2 5-171CLI Commandssetspeed Set the data rate for each DS0 to which a V.35 is crossconnected56 56K data rate64 64K data ratetxc
5-172 Axxius 800 - Release 2.2CLI Commandssetset (v54)Use the set (v54) command to setup V.54 Loopback Test Parameters. The command specifies the rang
Axxius 800 - Release 2.2 5-173CLI Commandsset[nnn] chart patternSyntax: set{v54-addr} v54 equipment pattern {n}Set V.54 test pattern n is from the fol
5-174 Axxius 800 - Release 2.2CLI Commandssetset verificationUse the set verification command to enable or disable verification prompts.Syntax: set ve
Axxius 800 - Release 2.2 5-175CLI CommandsshowshowThe following show commands are linked to a detailed description of each command.show (adpcm) show (
5-176 Axxius 800 - Release 2.2CLI Commandsshowshow (adpcm)Use the show (adpcm) command to display the settings for the ADPCM card.Syntax: show {adpcm-
Axxius 800 - Release 2.2 5-177CLI Commandsshowshow autoexitUse the show autoexit command to display whether autoexit is on or off. If on, the time-out
5-178 Axxius 800 - Release 2.2CLI Commandsshowshow cclabelsThe show cclabels command displays all user defined DS0 cross-connect labels. Syntax: show
Axxius 800 - Release 2.2 5-179CLI Commandsshowshow connectThe show connect command displays the static connections for channels and ports. Syntax: sho
xxviii Axxius 800 - Release 2.2Table of Contents 15 Terminal Server Router CardOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-180 Axxius 800 - Release 2.2CLI Commandsshowshow connect adpcmThe show connect adpcm command displays the connections for the ADPCM port. Syntax: sh
Axxius 800 - Release 2.2 5-181CLI Commandsshowshow (ds0)The show (ds0) command displays settings for DS0s. Syntax: show {ds0-addr}Example: show a:2:1-
5-182 Axxius 800 - Release 2.2CLI Commandsshowshow (ds1)The show (ds1) command displays settings for DS1s. Syntax: show {ds1-addr}Example: show 1:1SLO
Axxius 800 - Release 2.2 5-183CLI Commandsshowshow (ds3)The show (ds3) command displays the current settings for a DS3. Syntax: show {ds3-addr}Example
5-184 Axxius 800 - Release 2.2CLI Commandsshow{ds3-addr}In the form of {slot:port}.show ethernetThe show ethernet command displays Ethernet and IP set
Axxius 800 - Release 2.2 5-185CLI Commandsshowshow (fxo)The show (fxo) command displays the settings for FXOs.Syntax: show {fxo-addr}Example: show 7:1
5-186 Axxius 800 - Release 2.2CLI Commandsshowshow (fxsPS or fxsPSM)The show (fxsPS or fxsPSM) command displays the settings for the Single Channel PO
Axxius 800 - Release 2.2 5-187CLI Commandsshowshow imageThe show image command displays the application images stored in the Controller or Router.Synt
5-188 Axxius 800 - Release 2.2CLI Commandsshowshow impedanceThe show impedance command displays the impedance settings for FXS 5G card.Syntax: show im
Axxius 800 - Release 2.2 5-189CLI Commandsshowshow ipThe show ip command displays the IP Address information for the Axxius 800.Syntax: show ipExample
Axxius 800 - Release 2.2 xxix Table of Contents 16 V.35/.54 CardOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-190 Axxius 800 - Release 2.2CLI Commandsshowshow lsprotectThe show lsprotect command displays the low speed protection information.Syntax: show lspr
Axxius 800 - Release 2.2 5-191CLI Commandsshowshow ntpThe show ntp command displays settings for Network Time Protocol.Syntax: show ntpExample: show n
5-192 Axxius 800 - Release 2.2CLI Commandsshowshow radiusThe show radius command displays the RADIUS configuration settings for the Controller.Syntax:
Axxius 800 - Release 2.2 5-193CLI Commandsshowshow (router)The show (router) command displays the settings for the Router card.Syntax: show {rtr_card-
5-194 Axxius 800 - Release 2.2CLI CommandsshowSpanning Tree Protocol Settings for Router: Spanning Tree: DisabledSyslog Settings for Router:
Axxius 800 - Release 2.2 5-195CLI Commandsshowshow (router) dhcpThe show (router) dhcp command displays the current DHCP settings for the Router card.
5-196 Axxius 800 - Release 2.2CLI Commandsshowshow (router) dnsThe show (router) dns command displays the current DNS setup for the Router card.Syntax
Axxius 800 - Release 2.2 5-197CLI Commandsshowshow (router) lmiThe show (router) lmi command displays the current Local Management Interface (LMI) set
5-198 Axxius 800 - Release 2.2CLI Commandsshowshow (router) ntpThe show (router) ntp command displays settings for NTP options.Syntax: show {rtr_card-
Axxius 800 - Release 2.2 5-199CLI Commandsshowshow (router) portThe show (router) port command displays the current TSR ports configuration. This comm
PREFACEPrefaceComplianceSafetyThe Axxius 800 is certified by Underwriters Laboratories and is in compliance with UL60950, 3rd Edition; Safety of Infor
xxx Axxius 800 - Release 2.2Table of Contents Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-200 Axxius 800 - Release 2.2CLI Commandsshowshow (router) pppThe show (router) ppp command displays the current Local PPP (Point-to-Point Protocol)
Axxius 800 - Release 2.2 5-201CLI Commandsshowshow (router) ripThe show (router) rip command displays the current RIP settings for the Router card.Syn
5-202 Axxius 800 - Release 2.2CLI Commandsshowshow (router) stpThe show (router) stp command displays the current Spanning Tree Protocol settings for
Axxius 800 - Release 2.2 5-203CLI Commandsshowshow (router) uploaduser The show uploaduser command displays the current list of users allowed to uploa
5-204 Axxius 800 - Release 2.2CLI Commandsshowshow (router-lan)The show (router-lan) command displays the settings for the router card.Syntax: show {r
Axxius 800 - Release 2.2 5-205CLI Commandsshow Total: 0Static MAC Address Settings for LocalUnit: Total: 0LAN Filters Enabled for LocalUnit:
5-206 Axxius 800 - Release 2.2CLI Commandsshowshow (router-lan) filterThe show (router-lan) filter command displays the current LAN Layer 2 data filte
Axxius 800 - Release 2.2 5-207CLI Commandsshow{rtr_lan-addr}The Router address is in the form {slot:port} or {slot "profile-name"}[address|c
5-208 Axxius 800 - Release 2.2CLI Commandsshowshow (router-lan) staticThe show (router-lan) static commands to display the current list of static entr
Axxius 800 - Release 2.2 5-209CLI Commandsshowshow (router-lan) static ip networkThe show (router-lan) static ip network command displays the current
Axxius 800 - Release 2.2 xxxi Table of Contents C Loopback TestsAlarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-210 Axxius 800 - Release 2.2CLI Commandsshowshow (router-lan) static mac addressThe show (router-lan) static mac address command displays the curren
Axxius 800 - Release 2.2 5-211CLI Commandsshowshow (router-lan) stpThe show (router-lan) stp command displays the current Spanning Tree Protocol setti
5-212 Axxius 800 - Release 2.2CLI Commandsshowshow (router-wan)The show (router-wan) command displays the current configuration settings for the speci
Axxius 800 - Release 2.2 5-213CLI CommandsshowWAN Spanning Tree Protocol Settings for RemoteUnit: Spanning Tree: DisabledWAN Static IP Ne
5-214 Axxius 800 - Release 2.2CLI Commandsshowshow (router-wan) firewallThe show (router-wan) firewall command displays the current firewall filter se
Axxius 800 - Release 2.2 5-215CLI Commandsshowshow (router-wan) pppThe show (router-wan) ppp command displays the current PPP (Point-to-Point Protocol
5-216 Axxius 800 - Release 2.2CLI Commandsshowshow (router-wan) static ip addressThe show (router-wan) static ip address command displays the current
Axxius 800 - Release 2.2 5-217CLI Commandsshowshow (router-wan) static ipx networkThe show (router-wan) static ipx network command displays the curren
5-218 Axxius 800 - Release 2.2CLI Commandsshowshow (router-wan) static nat addressThe show (router-wan) static nat address command displays the curren
Axxius 800 - Release 2.2 5-219CLI Commandsshowshow (router-wan) trunkThe show (router-wan) trunk command displays the current trunk assignment for the
xxxii Axxius 800 - Release 2.2Table of Contents
5-220 Axxius 800 - Release 2.2CLI Commandsshowshow snmpThe show snmp command displays the SNMP settings.Example: show snmp SNMP Settings: System N
Axxius 800 - Release 2.2 5-221CLI Commandsshowshow timeThe show time command displays the system time, in 24 hour hh:mm:ss format.Syntax: show timeExa
5-222 Axxius 800 - Release 2.2CLI Commandsshowshow (v35)Use the show (v35) to display current settings for V.35 card.Syntax: show {v35-addr}Example: s
Axxius 800 - Release 2.2 5-223CLI Commandsshowshow (v54)Use the show (v54) to display current settings for V.54 card.Syntax: show {v54-addr}Example: s
5-224 Axxius 800 - Release 2.2CLI CommandsstatusstatusUse the status command to see the status of the system clocks, DS0s, DS1s, equipment, and the DS
Axxius 800 - Release 2.2 5-225CLI Commandsstatusstatus (adpcm)Use the status (adpcm) command to display the status information for the ADPCM card.Synt
5-226 Axxius 800 - Release 2.2CLI Commandsstatusstatus (adpcm) performanceUse the status (adpcm) performance command to display the performance statis
Axxius 800 - Release 2.2 5-227CLI Commandsstatusstatus (adpcm) performance historyUse the status (adpcm) performance history command to display perfor
5-228 Axxius 800 - Release 2.2CLI Commandsstatusstatus (bri)Use the status (bri) command to display the status information for the ISDN BRI card.Synta
Axxius 800 - Release 2.2 5-229CLI Commandsstatusstatus (bri) performanceUse the status (bri) performance command to display the performance statistics
CHAPTERBase PlatformIn this Chaptern Overviewn Featuresn Technical Specificationsn Chassisn Built-In Card Handlesn Management Portsn Local and
5-230 Axxius 800 - Release 2.2CLI Commandsstatusstatus (bri) performance historyUse the status (bri) performance history command to display the perfor
Axxius 800 - Release 2.2 5-231CLI Commandsstatusstatus (ds0)Use the status (ds0) command to display the current status of the specified DS0. Syntax: s
5-232 Axxius 800 - Release 2.2CLI Commandsstatusstatus (ds1)Use the status (ds1) command to display the current status of a DS1. Syntax: status {ds1-a
Axxius 800 - Release 2.2 5-233CLI Commandsstatusstatus (ds1) performanceUse the status (ds1) performance command to display the performance statistics
5-234 Axxius 800 - Release 2.2CLI Commandsstatusstatus (ds1) performance historyUse the status (ds1) performance history command to display performanc
Axxius 800 - Release 2.2 5-235CLI Commandsstatusstatus (ds3)Use the status (ds3) command to display the current status of the specified DS3. Syntax: s
5-236 Axxius 800 - Release 2.2CLI Commandsstatusstatus (ds3) performanceUse the status (ds3) performance command to display the performance statistics
Axxius 800 - Release 2.2 5-237CLI Commandsstatusstatus (ds3) performance historyUse the status (ds3) performance history command to display performanc
5-238 Axxius 800 - Release 2.2CLI Commandsstatusstatus equipmentUse the status equipment command to display current equipment information of the Axxiu
Axxius 800 - Release 2.2 5-239CLI CommandsstatusExample: status equipment 3The example with display the status of the card in slot 4. In this example
1-2 Axxius 800 - Release 2.2Base PlatformOverviewOverviewThe Axxius 800 Access Integration Platform solves today’s problems of multiple boxes, scalabi
5-240 Axxius 800 - Release 2.2CLI Commandsstatusstatus (fxsPS or fxsPSM)Use the status (fxsPS or FXS PSM) to display the current near-end line status
Axxius 800 - Release 2.2 5-241CLI Commandsstatusstatus lsprotect Use the status lsprotect command to display the current status of the low speed prote
5-242 Axxius 800 - Release 2.2CLI Commandsstatusstatus (ocudp) Use the status (ocudp) command to displaystatus for selftest and loopbacks. Syntax: sta
Axxius 800 - Release 2.2 5-243CLI Commandsstatusstatus (ocudp) performanceUse the status (ocudp) performance command to display performance statistics
5-244 Axxius 800 - Release 2.2CLI Commandsstatusstatus (ocudp) performance historyUse the status (ocudp) performance history command to display perfor
Axxius 800 - Release 2.2 5-245CLI Commandsstatusstatus (router)status (router) alarmsUse the status (router) alarms command to display the current ala
5-246 Axxius 800 - Release 2.2CLI Commandsstatusstatus (router) eventsUse the status (router) events command to display the current event log from the
Axxius 800 - Release 2.2 5-247CLI Commandsstatusstatus (router) ip address tableUse the status (router) ip address table command to display the curren
5-248 Axxius 800 - Release 2.2CLI Commandsstatusstatus (router) ip network tableUse the status (router) ip network table command to display the curren
Axxius 800 - Release 2.2 5-249CLI Commandsstatusstatus (router) ipx network tableUse the status (router) ipx network table command to display the curr
Axxius 800 - Release 2.2 1-3 Base PlatformFeaturesThe Control Panel Interface card provides front access to all the physical interfaces of the DS1 or
5-250 Axxius 800 - Release 2.2CLI Commandsstatusstatus (router) ipx server tableUse the status (router) ipx server table command to display the curren
Axxius 800 - Release 2.2 5-251CLI Commandsstatusstatus (router) mac address tableUse the status (router) mac address table command to display the curr
5-252 Axxius 800 - Release 2.2CLI Commandsstatusstatus (router) performanceUse the status (router) performance command to display the current runtime
Axxius 800 - Release 2.2 5-253CLI Commandsstatusstatus (router-lan)Use the status (router-lan) command to display the current Router status informatio
5-254 Axxius 800 - Release 2.2CLI Commandsstatusstatus (router-trunk)Use the status (router-trunk) command to display the current status information f
Axxius 800 - Release 2.2 5-255CLI Commandsstatusstatus sessionsUse the status sessions command to display the current status of all active CLI session
5-256 Axxius 800 - Release 2.2CLI Commandsstatusstatus (v54)Use the status (v54) to display the current near-end line status of the V.54 card.Syntax:
Axxius 800 - Release 2.2 5-257CLI CommandsstorestoreThe store command is used to upload a software file from a defined slot to a defined location on a
5-258 Axxius 800 - Release 2.2CLI Commandsswitchswitchswitch activeimageUse the switch activeimage command to switch the active with the backup applic
Axxius 800 - Release 2.2 5-259CLI Commandsswitchswitch (ds3) Use the switch (ds3) command to switch to the standby DS3 port. Note: for redundant Axxiu
1-4 Axxius 800 - Release 2.2Base PlatformControllersControllersThe Axxius 800 has two controllers available, one controller can support the system, ho
5-260 Axxius 800 - Release 2.2CLI Commandstelnettelnettelnet (router)Use the telnet (router) command to establish a Telnet session from the Axxius 800
Axxius 800 - Release 2.2 5-261CLI Commandstrace routetrace routetracert (router)Use the tracert (router) command to invoke a Trace Route to a host dev
5-262 Axxius 800 - Release 2.2CLI Commandstrace route{ip-addr|"domain-name"}[type][src-ip]This optional parameter, only applies it [type] is
CHAPTERDS1 Controller CardIn this Chaptern Overviewn Featuresn Technical Specificationsn Configurationn Built-In Card Handlesn LEDs
6-2 Axxius 800 - Release 2.2DS1 Controller CardOverviewOverviewThe Quad port DS1 Controller card drives the Axxius 800 Access Integration Platform, de
Axxius 800 - Release 2.2 6-3DS1 Controller CardFeaturesFeaturesl Rescues up to 35% or more of network bandwidth commonly wasted at the cell site or wh
6-4 Axxius 800 - Release 2.2DS1 Controller CardTechnical SpecificationsTechnical SpecificationsProduct Includesl Built-in non-blocking 1/0 Digital Cro
Axxius 800 - Release 2.2 6-5DS1 Controller CardTechnical SpecificationsManagementl Local- RS-232 craft port interface drives up to 50 ft. (15.24 m) ca
6-6 Axxius 800 - Release 2.2DS1 Controller CardTechnical SpecificationsService Interfaces Supportedl Dual V.35/.54 Service card (hardened)l FXO Voice
Axxius 800 - Release 2.2 6-7DS1 Controller CardTechnical SpecificationsAlarmsl Three visible alarm outputs, critical, major and minorl Three audible a
Axxius 800 - Release 2.2 1-5 Base PlatformService CardsOCU-DP Service cardThe OCU-DP service card is available in a Single or Quad port option. The OC
6-8 Axxius 800 - Release 2.2DS1 Controller CardController Active and StandbyController Active and StandbyThe Axxius 800 can function fully with a sing
Axxius 800 - Release 2.2 6-9DS1 Controller CardConfigurationConfigurationOptions on the Quad DS1 Controller card are set by the Command Line Interface
6-10 Axxius 800 - Release 2.2DS1 Controller CardBuilt-In Card HandlesBuilt-In Card HandlesThe Controller card is designed with a handle built into the
CHAPTERDS3 Controller CardIn this Chaptern Overviewn Featuresn Technical Specificationsn Configurationn Built-In Card Handlesn LEDs
7-2 Axxius 800 - Release 2.2DS3 Controller CardOverviewOverviewThe Dual port DS3 Controller card drives the Axxius 800 Access Integration Platform, de
Axxius 800 - Release 2.2 7-3 DS3 Controller CardFeaturesFeaturesl 2 DS3 ports built into the Controller deliver bandwidth to the resident cell site fo
7-4 Axxius 800 - Release 2.2DS3 Controller CardTechnical SpecificationsManagementl Local- RS-232 craft port interface drives up to 50 ft. (15.24 m) ca
Axxius 800 - Release 2.2 7-5 DS3 Controller CardTechnical SpecificationsService Interfaces Supportedl Dual V.35/.54 Service card (hardened)l FXO Voice
7-6 Axxius 800 - Release 2.2DS3 Controller CardTechnical SpecificationsTesting and Diagnosticsl Supports maintenance signals specified in ANSI T1.404
Axxius 800 - Release 2.2 7-7 DS3 Controller CardController Active and StandbyController Active and StandbyThe Axxius 800 can function fully with a sin
1-6 Axxius 800 - Release 2.2Base PlatformPower SuppliesLow Speed Protection cardLow speed protection provides backup circuitry for any T1 service port
7-8 Axxius 800 - Release 2.2DS3 Controller CardController and DS3 RedundancyController and DS3 RedundancyProtection ModesThe Axxius 800 can be provisi
Axxius 800 - Release 2.2 7-9 DS3 Controller CardController and DS3 Redundancyswitching the output paths so that the transmit path of the DS3 line is c
7-10 Axxius 800 - Release 2.2DS3 Controller CardController and DS3 RedundancyNetwork Protection ModeThe network mode of protection requires a single C
Axxius 800 - Release 2.2 7-11 DS3 Controller CardConfigurationConfigurationOptions on the DS3 Controller card are set by the following CLI commands.CL
7-12 Axxius 800 - Release 2.2DS3 Controller CardBuilt-In Card HandlesBuilt-In Card HandlesThe Controller card is designed with a handle built into the
CHAPTERFXO Voice CardIn this Chaptern Overviewn Featuresn Technical Specificationsn Card Configuration- CLI Commands- DIP Switch Settingsn LEDsn Chann
8-2 Axxius 800 - Release 2.2FXO Voice CardOverviewOverviewThe FXO Voice Service card provides high-density provisioning of reliable Foreign Exchange O
Axxius 800 - Release 2.2 8-3 FXO Voice CardFeaturesFeaturesl Delivers FXO or DID telephone services from T1 access circuitsl Supports CLASS services i
8-4 Axxius 800 - Release 2.2FXO Voice CardTechnical SpecificationsFXO Signaling Performancel DC Loop Range: > 1600Ω loop or ground startl Ringer Eq
Axxius 800 - Release 2.2 8-5 FXO Voice CardCard ConfigurationCard ConfigurationThe FXO voice card can be configured, to support either FXO loop start
Axxius 800 - Release 2.2 1-7 Base PlatformTechnical SpecificationsCapacitiesl 2 x Power Supply cardsl 2 x DS3 or DS1 Controller cardsl 1 x Control Pan
8-6 Axxius 800 - Release 2.2FXO Voice CardDIP Switch SettingsDIP Switch SettingsThe FXO card DIP switches are not functional on the Axxius 800 platfor
Axxius 800 - Release 2.2 8-7 FXO Voice CardChannel Associated Signaling (CAS) ConversionsChannel Associated Signaling (CAS) ConversionsCross-connects
8-8 Axxius 800 - Release 2.2FXO Voice CardChannel Associated Signaling (CAS) Conversions
CHAPTERISDN BRI CardIn this Chaptern Overviewn Featuresn Technical Specificationsn Card Configuration- CLI Commandsn LEDsn Connector Pinouts- Wire
9-2 Axxius 800 - Release 2.2ISDN BRI CardOverviewOverviewThe ISDN BRI Service Cards enable service providers and enterprises to deploy high-density, s
Axxius 800 - Release 2.2 9-3ISDN BRI CardFeaturesFeaturesl Enables carriers to economically bundle ISDN with all other services at 64 Kbps or 128 Kbps
9-4 Axxius 800 - Release 2.2ISDN BRI CardTechnical SpecificationsManagementl Standard ISDN SNMP MIB supportedNetwork Interfacel 3 DS0 mode: Uses 3 con
Axxius 800 - Release 2.2 9-5ISDN BRI CardTechnical SpecificationsPowerl Maximum power input: 6 W (8 port)l Solid-state fuseless protectionEnvironmentI
9-6 Axxius 800 - Release 2.2ISDN BRI CardCard ConfigurationCard Configuration BRI card options are set with the Command Line Interface (CLI). For addi
Axxius 800 - Release 2.2 9-7ISDN BRI CardLEDsLEDsThere is an LED for each ISDN BRI on a card. The function for each LED is listed below:State Descript
iv Axxius 800 - Release 2.2PrefaceComplianceThe Facility Interface Code (FIC) associated with each private line application represents the type of ser
1-8 Axxius 800 - Release 2.2Base PlatformTechnical SpecificationsAlarm ConnectorsThe alarm contact outputs are per Telcordia definitions for visible a
9-8 Axxius 800 - Release 2.2ISDN BRI CardConnector PinoutsConnector PinoutsWire-Wrap Pinout 2 Wire ServicesThe following pinout applies to the wire-wr
CHAPTEROCU-DP CardIn this Chaptern Overviewn Featuresn Technical Specificationsn Card Configuration- CLI Commands- Basic Setupn LEDsn Jumper S
10-2 Axxius 800 - Release 2.2OCU-DP CardOverviewOverviewThe Single Port and Quad Port all-rate OCU-DP Service Cards provide electrical and physical te
Axxius 800 - Release 2.2 10-3OCU-DP CardOverviewCustomer Premise ApplicationIn this model, the carrier deploys the Axxius 800 in conjunction with DDS
10-4 Axxius 800 - Release 2.2OCU-DP CardOverviewSS7 Backhaul ApplicationIn this application, the carrier uses the OCU to transfer signaling and call i
Axxius 800 - Release 2.2 10-5OCU-DP CardFeaturesFeaturesl Provides available baseband data rates from 2.4 to 72 Kbpsl Supports primary and secondary c
10-6 Axxius 800 - Release 2.2OCU-DP CardTechnical SpecificationsNetwork Interfacel Each OCU port DS0 cross-connected to T1 portLoopbacksOCU, CSU and D
Axxius 800 - Release 2.2 10-7OCU-DP CardCard ConfigurationCard Configuration OCU-DP card options are set with the Command Line Interface (CLI). For ad
10-8 Axxius 800 - Release 2.2OCU-DP CardCard ConfigurationBasic SetupCommand Descriptionset {ocudp-addr} baud {2400|4800|9600|19200|38400|56000*|64000
Axxius 800 - Release 2.2 10-9OCU-DP CardLEDsLEDsThere are two LEDs for each channel on the OCU-DP card. The function for each LED is listed below:Stat
Axxius 800 - Release 2.2 1-9 Base PlatformChassisChassisController RelayCardCards(A1 & A2)Service CardSlots 1-8PowerSupplies(P1 & P2)Future De
10-10 Axxius 800 - Release 2.2OCU-DP CardJumper SettingsJumper SettingsThe P1 and P2 Jumpers are defaulted to RJ-48S, which are the set of pins neares
Axxius 800 - Release 2.2 10-11OCU-DP CardAlarmsAlarmsThe OCU-DP cards and supporting Controller Software will support the following alarms:Alarm/Event
10-12 Axxius 800 - Release 2.2OCU-DP CardLine Rates/Line LengthsLine Rates/Line LengthsAll lengths were measured to meet a BER of 10-7 with up to 45 d
Axxius 800 - Release 2.2 10-13OCU-DP CardConnector PinoutsConnector PinoutsThe OCU-DP is part of the network, it connect to customer equipment.DDS RJ-
10-14 Axxius 800 - Release 2.2OCU-DP CardConnector PinoutsWire-Wrap Pinout 4 Wire ServicesThe following pinout applies to the wire-wrap pinout for the
CHAPTERSingle Channel POTS CardsIn this Chaptern Overview n Featuresn Technical Specificationsn Card Configuration- CLI Commandsn Connector Pino
11-2 Axxius 800 - Release 2.2Single Channel POTS CardsOverviewOverviewA Single Channel POTS card provides wireless service providers a standard FXS vo
Axxius 800 - Release 2.2 11-3Single Channel POTS CardsTechnical SpecificationsTechnical SpecificationsController Software Requiredl Release 1.0 or hig
11-4 Axxius 800 - Release 2.2Single Channel POTS CardsTechnical SpecificationsPhysicall POTS connections are through front panel RJ-11l Dimensions:
Axxius 800 - Release 2.2 11-5Single Channel POTS CardsBuilt-In Card HandlesBuilt-In Card HandlesThe Single Channel POTS cards are designed with a hand
1-10 Axxius 800 - Release 2.2Base PlatformBuilt-In Card HandlesBuilt-In Card HandlesSeveral of the cards for the Axxius 800 are designed with a handle
11-6 Axxius 800 - Release 2.2Single Channel POTS CardsConnector PinoutsConnector PinoutsRJ-11 Connector There is one RJ-11 (female) connector on the f
Axxius 800 - Release 2.2 11-7Single Channel POTS CardsLEDs LEDsThe POTs channel LED (left) status is described in the table below. The second LED (rig
11-8 Axxius 800 - Release 2.2Single Channel POTS CardsBasic ConfigurationBasic ConfigurationWARNING! DO NOT INSTALL TWO SINGLE CHANNEL POTS SERVICE
CHAPTERPower SupplyIn this Chaptern Overviewn Features n Technical Specificationsn Input Powern LEDsn Installing/Replacing a Power Supply
12-2 Axxius 800 - Release 2.2Power SupplyOverviewOverviewThe Axxius 800 Power Supply options operate from either 24 VDC or 48 VDC to supply 5V power t
Axxius 800 - Release 2.2 12-3Power SupplyTechnical SpecificationsTechnical SpecificationsComponentsl 24 VDC Power Supplyl 48 VDC NI48 Power Supplyl 48
12-4 Axxius 800 - Release 2.2Power SupplyTechnical SpecificationsAlarmsl Communicates status to Controller when 24 or 48 VDC input voltage is low Inte
Axxius 800 - Release 2.2 12-5Power SupplyInput PowerInput PowerThe following graphic displays the back of the Axxius chassis, with the Input power for
12-6 Axxius 800 - Release 2.2Power SupplyLEDsLEDsBoth power supply cards have identical LEDs, as described in the table below.
Axxius 800 - Release 2.2 12-7Power SupplyInstalling/Replacing a Power SupplyInstalling/Replacing a Power SupplyInstall a Power SupplyThe Axxius has re
Axxius 800 - Release 2.2 1-11 Base PlatformControl Panel InterfacesControl Panel InterfacesSMB connector (female)The recommended mate for the SMB conn
12-8 Axxius 800 - Release 2.2Power SupplyInstalling/Replacing a Power Supply
CHAPTERQuad DS1 ADPCM CardIn this Chapter n Overviewn Featuresn Technical Specificationsn Card Configuration- CLI Commands- Cross-Connects- Basic
13-2 Axxius 800 - Release 2.2Quad DS1 ADPCM CardOverviewOverviewThe Quad DS1 ADPCM Service card is a component of the Axxius 800 Access Integration Pl
Axxius 800 - Release 2.2 13-3Quad DS1 ADPCM CardFeaturesFeaturesl 32 Kbps ADPCM voice compressionl Supports Clear Channel Signaling and line formattin
13-4 Axxius 800 - Release 2.2Quad DS1 ADPCM CardTechnical SpecificationsT1 Interface (continued)l Jitter: meets AT&T Pub. TR-62411l Solid-state fu
Axxius 800 - Release 2.2 13-5Quad DS1 ADPCM CardTechnical SpecificationsAlarmsl Support standard T1.403 alarmsl LOS (Loss of Signal), Red, Yellow, Blu
13-6 Axxius 800 - Release 2.2Quad DS1 ADPCM CardCard ConfigurationCard ConfigurationAll options on the this Service card are set using the Command Lin
Axxius 800 - Release 2.2 13-7Quad DS1 ADPCM CardCard Configurationl show (adpcm)Displays current settings for the ADPCM card (circuit ID, up.down, fra
13-8 Axxius 800 - Release 2.2Quad DS1 ADPCM CardCard ConfigurationBasic SetupBefore configuring the DS1 ADPCM card, there are some basics that need to
Axxius 800 - Release 2.2 13-9Quad DS1 ADPCM CardCard ConfigurationCross-ConnectsIt is important to note that all timeslots are cross-connected in pair
1-12 Axxius 800 - Release 2.2Base PlatformControl Panel InterfacesRS-232 Craft Port (Female DB-9)The RS-232 craft port connects via a female DB-9 conn
13-10 Axxius 800 - Release 2.2Quad DS1 ADPCM CardJumper SettingsJumper SettingsThe P2 and P3 Jumpers are defaulted to RJ-48, which are the set of pins
Axxius 800 - Release 2.2 13-11Quad DS1 ADPCM CardConnector PinoutsConnector PinoutsRJ-48 Connector There are four RJ-48 (female) connectors on the fro
13-12 Axxius 800 - Release 2.2Quad DS1 ADPCM CardLEDsLEDsEach channel on the Quad DS1 ADPCM card has two LEDs. The description of the top LED is shown
CHAPTERQuad T1 & Quad DS1/E1 CardIn this Chapter n Overviewn Featuresn Technical Specificationsn Card Configuration- CLI Commandsn Jumper Set
14-2 Axxius 800 - Release 2.2Quad T1 & Quad DS1/E1 CardOverviewOverviewThe Hardened Quad T1 and DS1/E1 Service cards enable wireless service provi
Axxius 800 - Release 2.2 14-3Quad T1 & Quad DS1/E1 CardFeaturesFeaturesl Integrated T1 CSU functionality with FCC registration for direct connecti
14-4 Axxius 800 - Release 2.2Quad T1 & Quad DS1/E1 CardTechnical SpecificationsTechnical SpecificationsController Software Requiredl Release 1.0 o
Axxius 800 - Release 2.2 14-5Quad T1 & Quad DS1/E1 CardTechnical SpecificationsClockingl Loop-timed from any T1l External from BITS clock input (t
14-6 Axxius 800 - Release 2.2Quad T1 & Quad DS1/E1 CardTechnical SpecificationsEnvironmentIn addition to the systems environment requirements, the
Axxius 800 - Release 2.2 14-7Quad T1 & Quad DS1/E1 CardCard ConfigurationCard ConfigurationAll options on the this card are set using the Command
Axxius 800 - Release 2.2 1-13 Base PlatformControl Panel InterfacesDS1 Connection PortsThe DS1 connection ports are each equipped with a standard RJ-2
14-8 Axxius 800 - Release 2.2Quad T1 & Quad DS1/E1 CardJumper SettingsJumper SettingsThe P2 and P3 Jumpers are defaulted to RJ-48, which are the s
Axxius 800 - Release 2.2 14-9Quad T1 & Quad DS1/E1 CardConnector PinoutsConnector PinoutsRJ-48 Connector There are four RJ-48 (female) connectors
14-10 Axxius 800 - Release 2.2Quad T1 & Quad DS1/E1 CardLEDsLEDsEach channel on the card has two LEDs. The description of the top LED is shown bel
CHAPTERTerminal Server Router CardIn this Chapter n Overviewn Featuresn Technical Specificationsn Card Configuration- CLI Commandsn Connector Pi
15-2 Axxius 800 - Release 2.2Terminal Server Router CardOverviewOverviewThe Quad-Port Terminal Server Router (TSR) card combines the performance and e
Axxius 800 - Release 2.2 15-3Terminal Server Router CardFeaturesFeaturesl Enables remote management of cell site resourcesl Supplies 4 selectable RS-2
15-4 Axxius 800 - Release 2.2Terminal Server Router CardTechnical SpecificationsTechnical SpecificationsController Software Requiredl Release 1.0 or h
Axxius 800 - Release 2.2 15-5Terminal Server Router CardTechnical SpecificationsRS-232 Interfacel Up to 4 RS-232 DCE portsl Selectable asynchronous da
15-6 Axxius 800 - Release 2.2Terminal Server Router CardTechnical SpecificationsFrame Relayl RFC 1490 encapsulationl ANSI T1.617 Annex D LMIl ITU Q.93
Axxius 800 - Release 2.2 15-7Terminal Server Router CardTechnical SpecificationsEquipment Supported for TBOS-to-SNMP Conversionl Proxim Lynx.sc Microw
1-14 Axxius 800 - Release 2.2Base PlatformControl Panel InterfacesControl Panel Interface Card JumpersThe Control Panel Interface card is provided wit
15-8 Axxius 800 - Release 2.2Terminal Server Router CardCard ConfigurationCard ConfigurationThe Terminal Server Router card has the option of configur
Axxius 800 - Release 2.2 15-9Terminal Server Router CardCard Configurationl add (router-lan) filterAdd an address filter to the table of Layer 2 filte
15-10 Axxius 800 - Release 2.2Terminal Server Router CardCard Configurationl delete (router) static dns hostDelete a static DNS host record.l delete
Axxius 800 - Release 2.2 15-11Terminal Server Router CardCard Configurationl reset (router)Reboot the Router. All new configuration since the last con
15-12 Axxius 800 - Release 2.2Terminal Server Router CardCard Configurationl set (router) rebootSet automatic reboot after an upload of code or config
Axxius 800 - Release 2.2 15-13Terminal Server Router CardCard Configurationl set (router-wan) dlciConfigure the DLCI for a specified WAN interface tha
15-14 Axxius 800 - Release 2.2Terminal Server Router CardCard Configurationl show (router) dnsDisplays the current DNS settings for the TSR card.l sh
Axxius 800 - Release 2.2 15-15Terminal Server Router CardCard Configurationl show (router-lan) filterDisplays the current LAN Layer 2 data filters app
15-16 Axxius 800 - Release 2.2Terminal Server Router CardCard Configurationl status (router-trunk)Displays the current state of the DNS resolver and t
Axxius 800 - Release 2.2 15-17Terminal Server Router CardConnector PinoutConnector Pinout10Base-T EthernetThe pinout for the RJ-48C (female) connector
Axxius 800 - Release 2.2 1-15 Base PlatformControl Panel LEDsControl Panel LEDsAlarm LEDsLED State DescriptionCRITICAL Off No critical alarms presentR
15-18 Axxius 800 - Release 2.2Terminal Server Router CardConnector PinoutTSR Card JumpersThe jumpers on the TSR card select the use of the 10/100Base-
Axxius 800 - Release 2.2 15-19Terminal Server Router CardLEDsLEDsThe TSR service card has 2 LEDs per port.At Power-upNormal OperationPort Set for Ethe
15-20 Axxius 800 - Release 2.2Terminal Server Router CardLEDs
CHAPTERV.35/.54 CardIn this Chaptern Overviewn Featuresn Technical Specificationsn Card Configuration- CLI Commandsn Cablesn Connector Pinouts-
16-2 Axxius 800 - Release 2.2V.35/.54 CardOverviewOverview The Hardened Dual V.35/.54 Service card enables wireless service providers to provision con
Axxius 800 - Release 2.2 16-3V.35/.54 CardFeaturesFeaturesl Each port provides any n x 56/ 64 Kbps data rate up to 1.536 Mbps on each portl Full non-b
16-4 Axxius 800 - Release 2.2V.35/.54 CardTechnical SpecificationsTesting and Diagnostics (V.35/54 card)l Addressable V.54 loop up and loop down (127-
Axxius 800 - Release 2.2 16-5V.35/.54 CardCard ConfigurationCard ConfigurationThe V.35/54 card can be configured, using the Command Line Interface (CL
16-6 Axxius 800 - Release 2.2V.35/.54 CardCablesCablesDepending on your application, you will need to purchase one or more of the available Carrier Ac
Axxius 800 - Release 2.2 16-7V.35/.54 CardConnector PinoutsConnector PinoutsV.35 DCE (DB-26)The V.35 DCE data port connection is made at the sub-minia
1-16 Axxius 800 - Release 2.2Base PlatformControl Panel LEDsEthernet LEDsWhen Status LED is on or flashing:LED State DescriptionSTATUS Off Link DownGr
16-8 Axxius 800 - Release 2.2V.35/.54 CardConnector PinoutsLEDsEach V.35 port has an LED, with definitions as shown in the table below.Sub-miniature D
CHAPTERLow Speed Protection CardIn this Chaptern Overviewn Featuresn Technical Specificationsn Card Configuration-CLI Commands- Basic Setup of a P
17-2 Axxius 800 - Release 2.2Low Speed Protection CardOverviewOverviewLow speed protection provides backup circuitry for any T1 service port on a Quad
Axxius 800 - Release 2.2 17-3Low Speed Protection CardOverviewThe Backup CardA Quad T1 or Quad DS1 ADPCM service card can be configured as the “Backup
17-4 Axxius 800 - Release 2.2Low Speed Protection CardFeaturesFeaturesl Redundant 1:7 T1 interface protectionl Maintains service during card swapsl Fo
Axxius 800 - Release 2.2 17-5Low Speed Protection CardTechnical SpecificationsService Cards Supportedl Quad T1 Service Card (hardened)l DS1/E1 Service
17-6 Axxius 800 - Release 2.2Low Speed Protection CardCard ConfigurationCard Configuration CLI CommandsThe following commands are used to configure th
Axxius 800 - Release 2.2 17-7Low Speed Protection CardCard ConfigurationUse the following steps to set up a Protected System.1. Install a Relay card i
17-8 Axxius 800 - Release 2.2Low Speed Protection CardLEDsLEDsThe Low Speed Protection card has 10 LEDs, which are defined below.Each channel on the Q
CHAPTERMaintenanceIn this Chaptern Software Loading- Loading System Software via TFTP- Upgrading Software Levels via XModemn Backup Axxius 800 Configu
Axxius 800 - Release 2.2 1-17 Base PlatformACOACOThe Alarm Cutoff feature permits the operator to temporarily silence the alarm outputs while testing
18-2 Axxius 800 - Release 2.2MaintenanceSoftware LoadingSoftware LoadingLoading System Software via TFTP1. Login to the Axxius 800, using a terminal e
Axxius 800 - Release 2.2 18-3 MaintenanceSoftware LoadingLoading Router Software via TFTP1. Login to the Axxius 800, using a terminal emulation progra
18-4 Axxius 800 - Release 2.2MaintenanceSoftware Loadingload standby tftp {ip-addr} "file-name"CLI command to load software to the Standby C
Axxius 800 - Release 2.2 18-5 MaintenanceSoftware LoadingUpgrading System and Router Software via TFTP using ProxyRequired: - Router Service card (
18-6 Axxius 800 - Release 2.2MaintenanceSoftware Loading3. After download, the program will be loaded from RAM into the flash memory and the system wi
Axxius 800 - Release 2.2 18-7 MaintenanceSoftware LoadingUpgrading Software Levels via XModemThe following upgrade can also be performed through the P
18-8 Axxius 800 - Release 2.2MaintenanceSoftware Loading3. The binary file name is usually in the format: AxxiusAxxius.pkt. At 9600 baud, the file tra
Axxius 800 - Release 2.2 18-9 MaintenanceBackup Axxius 800 ConfigurationBackup Axxius 800 ConfigurationA text file from the current configuration can
18-10 Axxius 800 - Release 2.2MaintenanceBackup Axxius 800 ConfigurationLoad Controller Configuration1. Open HyperTerm session with the Axxius 800 uni
Axxius 800 - Release 2.2 18-11 MaintenanceHot Swap Service CardHot Swap Service CardTo Hot-Swap (replace) a service card while the unit is powered on,
Axxius 800 - Release 2.2 v PrefaceComplianceIndustry Canada CS-03Registration Number: IC: 2638A-800’’NOTICE: This equipment meets the applicable Indu
1-18 Axxius 800 - Release 2.2Base PlatformACO
18-12 Axxius 800 - Release 2.2MaintenanceHot Swap Service Card
APPENDIXRegulatory ApprovalsIn this AppendixThis appendix contains a chart of all the components of the Axxius 800 and their Regulatory Approvals.
A-2 Axxius 800 - Release 2.2Regulatory ApprovalsAxxius 800 Chassis UL60950 FCC Part 15, Class A FCC Part 68 NEBS Level 3 cert, type 2 & 4 equi
APPENDIXSNMP InterfaceIn this Appendixn Overviewn SNMP Basicsn Enterprise MIB Supportn Router Enterprise MIB Supportn Public MIB Supportn Router Publi
B-2 Axxius 800 - Release 2.2SNMP InterfaceOverviewOverviewThe Simple Network Management Protocol (SNMP) enables network operations centers (NOCs) to m
Axxius 800 - Release 2.2 B-3 SNMP InterfaceEnterprise MIB SupportEnterprise MIB SupportThis release is with full SNMPv1 and SNMPv2c support. Enterpris
B-4 Axxius 800 - Release 2.2SNMP InterfaceRouter Enterprise MIB SupportRouter Enterprise MIB SupportEnterprise MIB Name Enterprise MIB FilenameRouter
Axxius 800 - Release 2.2 B-5 SNMP InterfacePublic MIB SupportPublic MIB SupportMIB Table CommentsRFC1155 (RFC-1155-smi.MIB)RFC1212 (RFC-1212.MIB)RFC12
B-6 Axxius 800 - Release 2.2SNMP InterfacePublic MIB SupportMIB Table CommentsRFC2494 (DS0-MIB, DS0BUNDLE-MIB)dsx0ConfigTabledsx0ChanMappingTabledsx0B
Axxius 800 - Release 2.2 B-7 SNMP InterfaceRouter Public MIB SupportRouter Public MIB SupportMIB Table CommentsRFC1213 (RFC-1213-MIB) systeminterfaces
CHAPTERPhysical InstallationIn this Chaptern Unpacking and Inspection n Installation Environmentn Assembly of Axxius 800 n Rack Mounting
B-8 Axxius 800 - Release 2.2SNMP InterfaceSNMP Trap ReportsSNMP Trap ReportsThe Axxius 800 can send the following SNMP trap reports.Standard TrapsEnte
APPENDIXLoopback TestsIn this Appendixn Overviewn DS1 Loopbacksn V.35 Loopbacksn V.35/V.54 Loop
C-2 Axxius 800 - Release 2.2Loopback TestsAlarmsAlarmsTest AlarmThe Axxius 800 alarm functions can be manually tested using the following command for
Axxius 800 - Release 2.2 C-3 Loopback TestsAlarmsThe following are hyperlinks to all the card LED information:DS1 Controller Card, LEDsDS3 Controller
C-4 Axxius 800 - Release 2.2Loopback TestsAlarmsDisplay AlarmsUse the alarms command to display the active alarms. Each alarm is related to a particul
Axxius 800 - Release 2.2 C-5 Loopback TestsLogsLogsDisplay the event log to view a log of all system events, or narrow the view to only display specif
C-6 Axxius 800 - Release 2.2Loopback TestsStatus and PerformanceStatus and PerformanceThe following status commands will display vital information reg
Axxius 800 - Release 2.2 C-7 Loopback TestsOverviewOverviewA loopback test is a diagnostic procedure in which a signal is transmitted and returned to
C-8 Axxius 800 - Release 2.2Loopback TestsDS1 LoopbacksView Status of Loopback> status a:1SLOT A:Status for DS1 1: Receive: Tra
Axxius 800 - Release 2.2 C-9 Loopback TestsDS1 LoopbacksDS1 Payload LoopLoops at DS1 (in framer) and reframes the T1. Have DS1 vendor check for framin
2-2 Axxius 800 - Release 2.2Physical InstallationUnpacking and InspectionUnpacking and InspectionWARNING! OBSERVE PRECAUTIONS FOR HANDLING ELECTROST
C-10 Axxius 800 - Release 2.2Loopback TestsDS1 LoopbacksReceiving DS-1 CSU LoopCauses a line Loopback. Loopup code sent by remote unit or network. Occ
Axxius 800 - Release 2.2 C-11 Loopback TestsDS1 Loopbacks View Status of Loopback> show a:1SLOT A:Settings for DS1 1: Circuit ID:
C-12 Axxius 800 - Release 2.2Loopback TestsDS1 LoopbacksDS1 Equipment LoopNote: Quad T1 LED flashes green during equipment loop. Enable Equipment Loop
Axxius 800 - Release 2.2 C-13 Loopback TestsDS1 Loopbacks errored seconds: 0 0 sev. errored frame seconds:
C-14 Axxius 800 - Release 2.2Loopback TestsV.35 LoopbacksV.35 LoopbacksV.35 Line LoopNote: V.35 LED flashes green during line loop.Loop occurs at V.35
Axxius 800 - Release 2.2 C-15 Loopback TestsV.35 LoopbacksDisable Line Loopback > set 6:1 line loopdownOKView Status of Loopback > show 6:1SLOT
C-16 Axxius 800 - Release 2.2Loopback TestsV.35 LoopbacksV.35 Equipment LoopNote: V.35 LED flashes yellow during equipment loop.Loops at local V.35 po
Axxius 800 - Release 2.2 C-17 Loopback TestsV.35 LoopbacksDisable Equipment Loopback > set 6:1 equipment loopdownOKView Status of Loopback > sh
C-18 Axxius 800 - Release 2.2Loopback TestsV.35/V.54 LoopV.35/V.54 LoopV.35/V.54 Service Card DescriptionThe V.35 Card with V.54 Loop Test provides th
Axxius 800 - Release 2.2 C-19 Loopback TestsV.35/V.54 LoopV.54 LoopNote: Local LED flashes yellow, remote LED flashes green.Enable V.54 LoopWhere a V.
Axxius 800 - Release 2.2 2-3 Physical InstallationInstallation EnvironmentInstallation EnvironmentThe environment in which you are installing the Axxi
C-20 Axxius 800 - Release 2.2Loopback TestsV.35/V.54 LoopV.54 Equipment LoopbackEnable V.54 Equipment LoopupWhere a V.35/V.54 card is in slot 6.> s
Axxius 800 - Release 2.2 C-21 Loopback TestsV.35/V.54 Loop> status 6:1SLOT 6:Status for V35 PORT 1: DCD: High CTS: High DSR:
C-22 Axxius 800 - Release 2.2Loopback TestsV.35/V.54 Loop
GLOSSARY10Base-T The most widely installed Ethernet local area networks (LANs) use ordinary telephone twisted-pair wire. When used on Ethernet, this c
Glossary - 2 Axxius 800 - Release 2.2Glossaryauthorizationauthorization The process of granting or denying access to a network resource. Most computer
Axxius 800 - Release 2.2 Glossary - 3 Glossarybipolarbipolar The predominant signaling method used for digital transmission services, such as DDS and
Glossary - 4 Axxius 800 - Release 2.2Glossarybroadbandbroadband A technology that provides an extremely wide and fast bandwidth so that many people ca
Axxius 800 - Release 2.2 Glossary - 5 Glossarychannelchannel A generic term for a communications path on a given medium; multiplexing techniques allow
Glossary - 6 Axxius 800 - Release 2.2GlossaryConstant Bit Rate (CBR)Constant Bit Rate (CBR)Refers to the transmission properties that data, video and
Axxius 800 - Release 2.2 Glossary - 7 GlossaryDHCPDHCP Dynamic Host Configuration Protocol. DHCP is a network configuration that allows maintenance to
2-4 Axxius 800 - Release 2.2Physical InstallationAssembly of Axxius 800Assembly of Axxius 800The cards should be positioned according to the following
Glossary - 8 Axxius 800 - Release 2.2GlossaryE&M SignalingE&M Signaling A signaling arrangement that uses separate leads, called respectively
Axxius 800 - Release 2.2 Glossary - 9 Glossaryframeframe A fragment of data that is packaged into a frame format, which comprises a header, payload, a
Glossary - 10 Axxius 800 - Release 2.2GlossaryGUIGUI Graphical User Interface, pronounced "GOOEY". A set of screen presentations and metapho
Axxius 800 - Release 2.2 Glossary - 11 GlossaryISDN BRIISDN BRI Integrated Services Digital Network. BRI, which is 144,000 bits per second and designe
Glossary - 12 Axxius 800 - Release 2.2GlossaryLine Coding Violation (LCV)Line Coding Violation (LCV)This parameter is a count of both BPVs and EXZs oc
Axxius 800 - Release 2.2 Glossary - 13 GlossaryLULTLULT Line Unit Line TerminationLUNT Line Unit Network TerminationManagement Information Base (MIB)A
Glossary - 14 Axxius 800 - Release 2.2GlossaryNetwork Address Translation (NAT)Network Address Translation (NAT)An Internet standard that enables a lo
Axxius 800 - Release 2.2 Glossary - 15 GlossaryPassword Authentication Protocol (PAP)Password Authentication Protocol (PAP)An authentication protocol
Glossary - 16 Axxius 800 - Release 2.2Glossaryrobbed bitrobbed bit A type of analog signaling that will occasionally steal information bits used for c
Axxius 800 - Release 2.2 Glossary - 17 Glossarystar networkstar network A star is a network topology that connects all devices to a central location c
Axxius 800 - Release 2.2 2-5 Physical InstallationRack MountingRack MountingThe Axxius 800 can be mounted on a 19 or 23 inch rack with Carrier Access
Glossary - 18 Axxius 800 - Release 2.2GlossaryTBOSTBOS Telemetry Byte Oriented Serial. TBOS is an alarm monitoring and control prototype for telephone
Axxius 800 - Release 2.2 Glossary - 19 GlossaryV.90V.90 The standard for full-duplex modems sending and receiving data across phone lines at up to 56,
Glossary - 20 Axxius 800 - Release 2.2Glossary
INDEXNumerics10/100Base-T Ethernet Connector . . . . . . . .1-1310Base-T . . . . . . . . . . . . . . . . . . . . . .Glossary-126-pin micro-SCSIV.35 c
Index - 2 Axxius 800 - Release 2.2IndexCBase Platform . . . . . . . . . . . . . . . . . . . . . . . . 1-1ACO . . . . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2 Index - 3 IndexCstatic ipx network . . . . . . . . . . . . . .5-30static mac address . . . . . . . . . . . . . .5-31static
Index - 4 Axxius 800 - Release 2.2IndexC(fxo) . . . . . . . . . . . . . . . . . . . . . . . . . . 5-87(fxsPS) . . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2 Index - 5 IndexCenable/disable . . . . . . . . . . . . . .5-136syslog . . . . . . . . . . . . . . . . . . . . . .5-137enab
Index - 6 Axxius 800 - Release 2.2IndexClevel . . . . . . . . . . . . . . . . . . . . . . . 5-169password . . . . . . . . . . . . . . . . . . . . 5-1
Axxius 800 - Release 2.2 Index - 7 IndexDperformance command . . . . . . . . .5-233performance history . . . . . . . . . . .5-234(ds3) . . . . . .
2-6 Axxius 800 - Release 2.2Physical InstallationRack MountingTo maintain proper convection cooling, maintain at least 1/2 RU between the Axxius and a
Index - 8 Axxius 800 - Release 2.2IndexD(router)dhcp server option command . . . . . . . 5-44dns proxy command . . . . . . . . . . . . . . 5-44remot
Axxius 800 - Release 2.2 Index - 9 IndexEfeatures . . . . . . . . . . . . . . . . . . . . . . 16-3, 17-4LEDs . . . . . . . . . . . . . . . . . . . .
Index - 10 Axxius 800 - Release 2.2IndexLLlabelDS0 connection . . . . . . . . . . . . . . . . . . . . 5-74FXSPS connection . . . . . . . . . . . . .
Axxius 800 - Release 2.2 Index - 11 IndexQcommand . . . . . . . . . . . . . . . . . . . . . . . . .5-63pinouts . . . . . . . . . . . . . . . . . . .
Index - 12 Axxius 800 - Release 2.2IndexSconnector pinout . . . . . . . . . . . . . . . . . . . 1-12data port . . . . . . . . . . . . . . . . . . .
Axxius 800 - Release 2.2 Index - 13 IndexSpassword command . . . . . . . . . . . .5-120prompt command . . . . . . . . . . . . .5-121protocolport com
Index - 14 Axxius 800 - Release 2.2IndexSenable/disable command . . . . . . . 5-163port cost command . . . . . . . . . . . . 5-164port priority com
Axxius 800 - Release 2.2 Index - 15 IndexSppp command . . . . . . . . . . . . . . . . . .5-215staticip address command . . . . . . . . . . .5-216ip
Index - 16 Axxius 800 - Release 2.2IndexTstp command . . . . . . . . . . . . . . . . . . . 5-252(router-lan) . . . . . . . . . . . . . . . . . . . .
CHAPTERElectrical Installation and CablingIn this Chapter n Compliant Installationn Chassis Connectionsn Power Connectionsn External Alarm Inputsn Vis
3-2 Axxius 800 - Release 2.2Electrical Installation and CablingCompliant InstallationCompliant InstallationWARNING! ALL TELECOMMUNICATION NETWORK CO
Axxius 800 - Release 2.2 3-3 Electrical Installation and CablingCompliant InstallationFerrite BeadsTo be compliant with FCC Part 15 EMI limits with t
vi Axxius 800 - Release 2.2PrefaceSafety InformationSafety InformationCAUTION! ALWAYS USE CAUTION WHEN INSTALLING TELEPHONE LINES. READ THE CAUTIONS
3-4 Axxius 800 - Release 2.2Electrical Installation and CablingChassis ConnectionsChassis ConnectionsThe following illustrations show all connectors o
Axxius 800 - Release 2.2 3-5 Electrical Installation and CablingChassis ConnectionsFront of the Axxius 800 - Interface Cardl 10Base-T Ethernet (RJ-4
3-6 Axxius 800 - Release 2.2Electrical Installation and CablingChassis ConnectionsChassis Ground Connector1. Route wire (#6 or #8 AWG copper) from bui
Axxius 800 - Release 2.2 3-7 Electrical Installation and CablingChassis ConnectionsPower ConnectionsThere are three power supplies available with the
3-8 Axxius 800 - Release 2.2Electrical Installation and CablingChassis Connections5. Ensure that no bare wire shows after the wires are installed. 6.
Axxius 800 - Release 2.2 3-9 Electrical Installation and CablingChassis ConnectionsExternal Alarm InputsThe external alarm input connector supports 1
3-10 Axxius 800 - Release 2.2Electrical Installation and CablingChassis ConnectionsVisible and Audible AlarmsThe external alarm connectors are six-pin
Axxius 800 - Release 2.2 3-11 Electrical Installation and CablingChassis ConnectionsBITS Clock 1/BITS Clock 2The external alarm connectors are three-
3-12 Axxius 800 - Release 2.2Electrical Installation and CablingChassis ConnectionsSlot (1-8) Wire-Wrap ConnectorsThe Axxius 800 provides wire-wrap co
Axxius 800 - Release 2.2 3-13 Electrical Installation and CablingChassis ConnectionsWire-Wrap Pinout for 4 Wire ServicesWire-Wrap Pins T1 Name Descri
Axxius 800 - Release 2.2 vii PrefaceNoticesNoticesThis manual contains important information and warnings that must be followed to ensure safe operati
3-14 Axxius 800 - Release 2.2Electrical Installation and CablingChassis ConnectionsWire-Wrap Pinout 2 Wire ServicesWire-Wrap Pins DescriptionT1 Channe
Axxius 800 - Release 2.2 3-15 Electrical Installation and CablingChassis ConnectionsStandard Telco Color CodeCircuit connections are made at the wire
3-16 Axxius 800 - Release 2.2Electrical Installation and CablingChassis ConnectionsPair Pin Location Function Color Code15 4015Tip Channel 15 Ring Cha
CHAPTERConfigurationIn this Chaptern Setting up a CLI Connectionn System Informationn Basic System Setupn Quick Configuration Reloadn Setup of DS0 Man
4-2 Axxius 800 - Release 2.2ConfigurationSetting up a CLI ConnectionSetting up a CLI ConnectionNOTE: The Default IP address of the Axxius 800 Control
Axxius 800 - Release 2.2 4-3 ConfigurationSystem InformationSystem InformationOnce a management session has bee initiated (Telnet or Hyperterm) the sy
4-4 Axxius 800 - Release 2.2ConfigurationBasic System SetupBasic System SetupInitial SetupUse the following commands for your initial setup, for furth
Axxius 800 - Release 2.2 4-5 ConfigurationBasic System SetupSet Up SecurityUse the following commands to set up the security on the Axxius 800.Set Up
4-6 Axxius 800 - Release 2.2ConfigurationBasic System SetupSet Up a DS0/Channel Use the following commands to set up a DS0. Set Up a DS1/T1Use the fol
Axxius 800 - Release 2.2 4-7 ConfigurationBasic System SetupSet Up a DS3Use the following commands to set up a DS3. See the set (ds3) command for more
viii Axxius 800 - Release 2.2PrefaceElectrostatic Discharge (ESD) PrecautionsElectrostatic Discharge (ESD) PrecautionsESD can damage processors, circu
4-8 Axxius 800 - Release 2.2ConfigurationBasic System SetupEstablish a Static Channel ConnectionUse the following commands to establish a static chann
Axxius 800 - Release 2.2 4-9 ConfigurationBasic System SetupSetup of ADPCMSet Up a V.35 PortUse the following commands to set up a V.35 port. Command
4-10 Axxius 800 - Release 2.2ConfigurationBasic System SetupSet Up a Single Channel POTS card Use the following commands to set up a POTS card.Change
Axxius 800 - Release 2.2 4-11 ConfigurationQuick Configuration ReloadQuick Configuration Reload The print config command can be used as a quick way to
4-12 Axxius 800 - Release 2.2ConfigurationQuick Configuration Reload5. Select the [START] button, the window will close and the operator will be retur
Axxius 800 - Release 2.2 4-13 ConfigurationQuick Configuration Reload3. Select the ASCII Setup button.4. Set the Line delay to 50 milliseconds and the
4-14 Axxius 800 - Release 2.2ConfigurationSetup of DS0 Management ChannelSetup of DS0 Management ChannelThe DS0 Management Channel provides an alterna
Axxius 800 - Release 2.2 4-15 ConfigurationSetup of DS0 Management ChannelEquipment Requiredl Access Navigator (version 1.7)l (1) Collocated RouterThi
4-16 Axxius 800 - Release 2.2ConfigurationSetup of DS0 Management ChannelThe following is the Address and DS1 assignments used in this example. This w
Axxius 800 - Release 2.2 4-17 ConfigurationSetup of DS0 Management ChannelSet IP Configuration of PC1. Set IP Address to 192.168.201.1022. Set Gateway
Axxius 800 - Release 2.2 ix PrefaceWarrantyWarrantyCarrier Access Corporation conditionally warrants to BUYER that PRODUCTS are free from substantial
4-18 Axxius 800 - Release 2.2ConfigurationSetup of DS0 Management ChannelAdd and Enable all Remote Axxius NeededTelnet into the TSR card1. From the CL
Axxius 800 - Release 2.2 4-19 ConfigurationSetup of DS0 Management ChannelConfigure Trunk Connections1. Select Configuration < Profile Directory &g
4-20 Axxius 800 - Release 2.2ConfigurationSetup of DS0 Management Channel4. For all WAN port numbers already assigned a DS0 for management select <
Axxius 800 - Release 2.2 4-21 ConfigurationSetup of DS0 Management Channel3. Set the following on this screen:Select the IP Protocol Eth II (X), all o
4-22 Axxius 800 - Release 2.2ConfigurationSetup of DS0 Management Channel2. Set the following on this screen:Rename RemoteUnit (default name) to Axxiu
Axxius 800 - Release 2.2 4-23 ConfigurationSetup of DS0 Management Channel6. Set Device Name to Axxius1Set the IP Address to 192.168.202.1 (Axxius1 WA
4-24 Axxius 800 - Release 2.2ConfigurationSetup of DS0 Management Channel9. Select the following on this screen:At the Select WAN Port Number: < No
Axxius 800 - Release 2.2 4-25 ConfigurationSetup of DS0 Management ChannelReinitialize the Router1. Select Exit <Reinitialize > from the Router
4-26 Axxius 800 - Release 2.2ConfigurationSetup of DS0 Management ChannelConfiguration of Remote AxxiusNote: The Ethernet cannot be connected to the R
Axxius 800 - Release 2.2 4-27 ConfigurationSetup of DS0 Management ChannelConfiguration of Access NavigatorNote: The Ethernet cannot be connected to t
Kommentare zu diesen Handbüchern